木材及木基結構材料檢測

木材及木基結構材料檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB 50005-2017木結構設計標準

本標準適用于建筑工程中方木原木結構、膠合木結構和輕型木結構的設計。

GB/T 51226-2017多高層木結構建筑技術標準

本標準適用于多層木結構民用建筑、高層木結構住宅建筑和辦公建筑的設計、制作、安裝、驗收與維護。

ASTM D4761-2005木材及木基結構材料機械性能的標準試驗方法

These test methods provide procedures that are applicable under true field conditions, such as in a plant with specimens not at moisture equilibrium. The data established by these test methods can be used as follows: 4.2.1 Develop strength and stiffness properties for the population represented by the material being tested (that is, individual grades, grade combinations, species, species groups, or any other defined, identifiable sample). 4.2.2 Confirm the validity of strength and stiffness properties for the population represented by the material being tested. 4.2.3 Investigate the effect of parameters that may influence the strength and stiffness properties of the material, such as moisture content, temperature, knot size and location, or slope of grain. The procedures chosen in accordance with these test methods shall be fully documented in the report to facilitate correlation with test results obtained through the use of traditional procedures, such as those set forth in Test Methods D 198.Note 18212;A proof load may be used, which will permit the determination of a specified strength percentile without testing the total sample to destruction. Designing a test program on the basis of proof loading can be complex, requiring consideration in relation to the objectives of the test program. Guidance on this matter can be found in the paper by Johnson.1.1 These test methods cover the determination of the mechanical properties of stress-graded lumber and other wood-base structural material.1.2 These test methods appear in the following order: SectionBending edge-wiseBending flat-wise:Center point loadingThird point loading Axial strength in tensionAxial strength in compression 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D4761-2011木材及木基結構材料機械性質的標準試驗方法

These test methods provide procedures that are applicable under true field conditions, such as in a plant with specimens not at moisture equilibrium. The data established by these test methods can be used as follows: Develop strength and stiffness properties for the population represented by the material being tested (that is, individual grades, grade combinations, species, species groups, or any other defined, identifiable sample). Confirm the validity of strength and stiffness properties for the population represented by the material being tested. Investigate the effect of parameters that may influence the strength and stiffness properties of the material, such as moisture content, temperature, knot size and location, or slope of grain. The procedures chosen in accordance with these test methods shall be fully documented in the report to facilitate correlation with test results obtained through the use of traditional procedures, such as those set forth in Test Methods D198.1.1 These test methods cover the determination of the mechanical properties of stress-graded lumber and other wood-base structural material. 1.2 These test methods appear in the following order: Section Bending edge-wise6 Bending flat-wise: Center point loading7 Third point loading8 Axial strength in tension9 Axial strength in compression 10 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D4761-2013木材及木基結構材料機械性質的標準試驗方法

4.1x00a0;These test methods provide procedures that are applicable under true field conditions, such as in a plant with specimens not at moisture equilibrium. 4.2x00a0;The data established by these test methods can be used as follows: 4.2.1x00a0;Develop strength and stiffness properties for the population represented by the material being tested (that is, individual grades, grade combinations, species, species groups, or any other defined, identifiable sample). 4.2.2x00a0;Confirm the validity of strength and stiffness properties for the population represented by the material being tested. 4.2.3x00a0;Investigate the effect of parameters that may influence the strength and stiffness properties of the material, such as moisture content, temperature, knot size and location, or slope of grain. 4.3x00a0;The procedures chosen in accordance with these test methods shall be fully documented in the report to facilitate correlation with test results obtained through the use of traditional procedures, such as those set forth in Test Methods D198. 1.1x00a0;These test methods cover the determination of the mechanical properties of stress-graded lumber and other wood-base structural material. 1.2x00a0;These test methods appear in the following order: x00a0; Section Bending edge-wise 6 Bending flat-wise: x00a0; 8199;Center point loading 7 8199;Third point loading 8 Axial strength in tension 9 Axial strength in compression