家用和類似用途固定電氣設備開關檢測

家用和類似用途固定電氣設備開關檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB 4793.1-2007測量、控制和實驗室用電氣設備的安全要求 第1部分：通用要求

1.1．1 本部分適用的設備GB 4793的本部分規定了預定作用、工業過程用以及教育用的電氣設備的通用安全要求，當在1．4的環境條件下使用時，這些符合下列a)～d)定義的任何一種設備可以配備計算裝置： a) 電氣試驗和測量設備 是指用電氣方法試驗、測量、指示或記錄一個或多個電量或非電量的設備，也包括非測量設備，如信號發生器、測量標準器、電源、換能器和發射機等。 注：除了設計成僅嵌裝在其他設備上的面板儀表外．所有指示和記錄用的電氣測量儀器(1．1．2的那些設備除外)均在GB 4793的范圍內。嵌裝式面板儀表被認為是元件，僅需要滿足GB 4793的相關要求，或者作為嵌裝這些儀表的設備的一個部件滿足其他標準。 b) 電氣控制設備 是指將一個或多個輸出量控制在特定量值的設備，而且每一個量值由手動設置、本地或遠地編程，或者由一個或多個輸入變量來確定的。 c) 電氣實驗室設備 是指測量、指示、監視或分析物質的設備，或者用于制備材料的設備，包括體外診斷(IVD)設備。 這種設備也可用于實驗室以外的地方，例如自我檢查用的IVD設備就可以在家庭中使用。 d) 預定要與上述設備一起使用的附件(例如樣品處理設備)。1．1．2不包括在本部分范圍內的設備 不適用于包括在下列標準范圍內的設備： a) GB 8898(音頻、視頻及類似電子設備安全要求)； b) GB 4706(家用和類似用途電器的’安全)； c) GB 4943(信息技術設備的安全，但1．1．3規定的設備除外)； d)GB 9706(醫用電氣設備)； e) GB/T 15283(0．5、1和2級交流有功電度表)； f) GB l9212(電力變壓器、電源裝置和類似產品的安全)； g)IEC 60204(電氣機械控制裝置)； h)IEC 60364(建筑物電氣裝置)； i)IEC 60439-1(低壓開關裝置和控制裝置)。1．1．3 計算設備本部分僅適用于組成本部分范圍內的設備的一部分或設計成僅與設備一起使用的計算機、處理器等。 注：在GB 4943范圍內的并符合其要求的汁算裝置和類似設備被認為適合與本部分范圍內的設備一起使用。但是，GB 4943對防潮和防液體的某些要求沒有本部分嚴格。如果潮濕和液體引起的危險可能會影響符合GB 4943的設備，而且該符合GB 4943的設備如果又與符合本部分的設備一起使用，則使用說明要規定出所需要的任何附加的預防措施。

GB/T 12668.501-2013調速電氣傳動系統 第5-1部分:安全要求 電氣、熱和能量

GB 12668的本部分規定了對調速電氣傳動系統或其元件有關電氣、熱和能量安全方面的要求。除接口要求外,本部分不覆蓋被傳動設備。本部分適用于包括電力變流設備、傳動控制設備和電動機的調速電氣傳動系統。但不包括牽引傳動和電動車輛傳動,本部分適用于連接交流電源電壓1 kV及以下,50 Hz或60 Hz的直流傳動系統以及變流器輸入或輸出電壓35 kV以下,50 Hz或60 Hz的交流傳動系統?！墩{(diào)速電氣傳動系統》的其他部分涉及額定值的規定、電磁兼容性(EMC)及功能安全性等。如果用作電氣傳動系統(PDS)組成部分的設備符合相應環境下有關產品標準的安全要求,則本部分的范圍不包括這些設備。例如,PDS中所使用的電動機就應當符合IEC 60034相關部分的要求。除非有特別規定,本部分的要求適用于PDS的所有部分,包括CDM/BDM(見圖1)。

GB/T 29600-2012移動實驗室用溫濕度控制系統技術規范

本標準規定了移動實驗室用溫濕度控制系統的術語和定義、技術要求、試驗方法。本標準適用于各類陸地移動實驗室溫濕度控制系統的通用技術條件。

GB/T 30843.3-20171 kV以上不超過35 kV的通用變頻調速設備 第3部分:安全規程

GB/T 30843的本部分規定了通用變頻調速設備或其元件有關電氣、熱和能量等除供電電源以外安全方面的要求。本部分不覆蓋用于牽引和電動車輛的變頻調速設備、電動機等。本部分適用于額定輸入電壓在交流1 kV~35 kV之間，額定輸入頻率為50 Hz或60 Hz，輸出電壓不超過35 kV，輸出頻率小于120 Hz的通用變頻調速設備(以下簡稱“變頻調速設備”)。

GB/T 30844.3-20171 kV及以下通用變頻調速設備 第3部分:安全規程

GB/T 30844的本部分規定了通用變頻調速設備或其元件有關電氣、熱和能量等除供電電源以外安全方面的要求。本部分不覆蓋用于牽引和電動車輛的變頻調速設備、電動機等。本部分適用于額定輸入電壓為交流1 kV等級及以下，額定輸入頻率為50 Hz或60 Hz，輸出電壓不超過1 kV，輸出頻率小于600 Hz的通用變頻調速設備(以下簡稱變頻調速設備)。

GB/T 32705-2016實驗室儀器及設備安全規范 儀用電源

本標準規定了正常和擴展的環境條件下，實驗室用反應釜的安全要求(不包括玻璃反應釜的安全要求)。本標準適用于預定用作由電網電源供電的獨立電源的通用安全要求，但不包括不間斷電源、設備內部不獨立銷售的電源。

GB/T 32708-2016實驗室儀器及設備安全規范 反應釜

本標準規定了正常和擴展的環境條件下(見附錄A)，實驗室用反應釜的安全要求(不包括玻璃反應釜的安全要求)。本標準也規定了通過檢查和型式試驗來鑒定設備是否符合本標準要求的方法。本標準適用于幾何容積小于25 L，設計壓力不大于35 MPa的反應釜。

GB/T 51188-2016建筑與工業給水排水系統安全評價標準

本標準適用于新建、擴建、改建和既有建筑與工業的給水排水系統安全評價。本規范不適用于軍工等特殊行業建筑與工業的給水排水系統安全評價。

YC/T 384.2-2018煙草企業安全生產標準化規范 第2部分:安全技術和現場規范

YC/T 284的本部分規定了煙草企業安全生產標準化的安全技術和現場規范要求，包括設備設施、作業活動、作業環境和現場運行的安全要求。本部分適用于省級煙草公司(局)、省級工業公司等省級公司、煙草加工和煙草商業生產經營單位。其中，煙草商業生產經營單位特指地市級煙草公司，煙草加工單位含煙葉復烤、卷煙制造、雪茄煙制造、再造煙葉生產的單位。煙草配套和多元化投資的其他生產經營單位，如醋酸纖維、煙草印刷等單位可參照執行。

UL 1740-2007機器人和自動設備

These requirements cover robots and robotic equipment rated 600 V or less and intended for installation in accordance with the National Electrical Code, ANSI/NFPA 70. Since end-use installation of a robot and robotic equipment may vary for each user application, guidelines for end-product installation may be evaluated to the applicable sections of ANSI/RIA R15.06, Standard for Industrial Robots and Robot Systems-Safety Requirements. Portions of the requirements in this Standard have been excerpted from the Robotic Industries Associations (RIA) Standard for Industrial Robots and Robot Systems - Safety Requirements, ANSI/RIA R15.06. These requirements cover robotic equipment and systems intended for indoor and outdoor use in applications such as parts assembly, parts transfer, automated material handling, inspection, loading, diecasting, deburring, welding, paint spraying, clinical/diagnostic systems, pharmaceutical applications, commercial food processing, automated vehicle refueling systems, library book handling/sorting, clean room applications, medical use for surgery, mobile robots, automated guided vehicles, automated storage/retrieval systems, and the like. Unique features or functions associated with the robotic application, not specifically addressed in this Standard, shall also be evaluated to other applicable Standards/requirements. These may include, but are not limited to, Electrical Equipment for Laboratory Use; Part 1: General Requirements, UL 3101-1; Medical and Dental Equipment, UL 544; Power Operated Pumps for Petroleum Product Dispensing Systems, UL 79. In addition to the requirements in this Standard, robots and robotic systems shall also comply with the applicable sections of the Electrical Standard for Industrial Machinery, ANSI/NFPA 79. Robots and robotic systems intended for use in hazardous locations, as defined by the National Electrical Code ANSI/NFPA 70, shall also comply with the requirements in Intrinsically Safe Apparatus and Associated Apparatus for Use in Class I, II, and III, Division 1, Hazardous (Classified) Locations, UL 913. In the following text, a requirement that applies to one type of equipment, such as a controller or teach pendant, will be identified by a specific reference. In the absence of a specific reference or if the term robot or robotic equipment is employed, it is to be understood that the requirement applies to all types of equipment covered by this Standard.

BS 5733-2010+A1-2014電器附件的一般要求. 規范

This British Standard specifies requirements and tests to check the safety in normal use of electrical accessories which are not covered by other specific British Standards.Such accessories are intended for use in household, commercial and light industrial premises where:?the nominal supply voltage does not exceed 250 V a.c. single-phase, 50 Hz to 60 Hz or 250 V d.c.;?the rated current of the accessory does not exceed 63 A.

BS EN 14637-2007建筑五金件.防火門/防煙門組件用電控開門系統.要求、試驗方法、應用和維修

This European Standard specifies requirements, methods of test and performance criteria against which thecompatibility of components and their performance can be assessed when used in combination to form anelectrically controlled hold-open system. It also specifies requirements for the integrity of such hold-opensystems when connected to fire detection and fire alarm systems or other systems, including the signalexchange and technical data for interfaces.This European Standard provides requirements for the application of electrically controlled hold-open systemsused for fire/smoke doors in buildings, where such doors are required to be self-closing. It covers planning,design (see Annex A), installation (see Annex B), commissioning, use and maintenance (see Annex E) ofhold-open systems, intended for the protection of life and/or the protection of property. This may also includehold-open systems, or components of the hold-open system, that are self-contained in a single enclosure.Electrically controlled hold-open systems manufactured, installed and serviced in accordance with thisEuropean Standard are recommended for use wherever there is a requirement for reliable hold-open andrelease of an individual self-closing fire/smoke door assembly in the case of fire.The use of hold-open systems for closures in conveyor systems conforming to EN 1366-7, which applies inconjunction with EN 1363-1, may require additional proof of suitability, which is not covered by this EuropeanStandard.This European Standard does not cover design, installation, commissioning, use and maintenance of buildingfire detection and fire alarm systems (covered by CEN/TS 54-14) but does cover the connection of hold-opensystems conforming to this European Standard to building fire detection and fire alarm systems, under certainprescribed conditions.This European Standard does not cover the requirements of performance characteristics and operationalenvironment conditions of particular components of a hold-open system, where these requirements arealready covered by European specifications, and which include appropriate test methods to assurereproducible test results for the product conformity assessment. These European Standards are referred to inClause 5.This European Standard does not cover electrically controlled systems used for smoke venting purposes orsystems that allow the door to remain open under fault conditions (i.e. not fail-safe).This European Standard does not cover electrically controlled hold-open systems that are not connected tomain power supply and are battery powered only.

BS EN 60204-32-2008機械安全.機械的電氣設備.起重機要求

This part of IEC 60204 applies to the application of electrical and electronic equipment andsystems to hoisting machines and related equipment.

BS EN 60669-2-1-2004+A12-2010家用及類似的固定電氣設施用開關.詳細要求.電子開關

This clause of part 1 applies except as follows.Replacement:This standard applies to electronic switches and to associated electronic extension units forhousehold and similar fixed electrical installations either indoors or outdoors.It applies to electronic switches for a.c. only, for the operation of lamp circuits and the controlof the brightness of lamps (dimmers) as well as the control of the speed of motors (forexample, those used in ventilating fans) and for other purposes (for example, heating controls),with a rated voltage not exceeding 250 V and a rated current not exceeding 16 A.The operation and/or control as mentioned above are performed by a person via an actuatingmember, a sensing surface or a sensing unit, by means of touch, proximity, turn, optical,acoustic, thermal or any other influence.This standard also applies to general purpose electronic switches with included automaticfunctions where the operation and/or the control is initiated by a change of a physicalquantity, for example light, temperature, humidity, time, wind velocity, presence of persons,etc.This standard also applies to boxes for electronic switches, with the exception of mountingboxes for flush-type electronic switches.This standard also applies to electronic RCS and electronic TDS with a rated voltage notexceeding 440 V and a rated current not exceeding 25 A, intended for household and similarfixed electrical installations, either indoors or outdoors.

BS EN 60669-2-3-2006家用和類似用途固定電氣設備用開關.專用要求.延時開關(TDS)

This clause of part 1 is applicable except as follows:Replacement of the first paragraph by:This part of IEC 60669 applies to time-delay switches (hereinafter referred to as TDS) with arated voltage not exceeding 440 V and a rated current not exceeding 63 A, intended forhousehold and similar fixed electrical installations, either indoors or outdoors, operated byhand and/or by remote control.TDS are provided with a time-delay device operated by mechanical, thermal, pneumatic,hydraulic or electrical means or by a combination of them.Electronic TDS are within the scope of IEC 60669-2-1.TDS including only passive components such as resistors, capacitors, PTC and NTCcomponents and printed wiring boards are not considered to be electronic TDS.

BS EN 61058-2-5-2011器具開關.轉換選擇器特定要求

1.1 This International Standard applies to change-over selectors (mechanical or electronic)for appliances actuated by hand, by foot or by other human activity, to operate or controlelectrical appliances and other equipment for household or similar purposes with a ratedvoltage not exceeding 480 V and a rated current not exceeding 63 A.These change-over selectors are intended to be operated by a person, via an actuatingmember or by actuating a sensing unit. The actuating member or sensing unit can be integralwith or arranged separately, either physically or electrically, from the switch and may involvetransmission of a signal, for example electrical, optical, acoustic or thermal, between theactuating member or sensing unit and the switch.Change-over selectors which incorporate additional control functions governed by the switchfunction are within the scope of this standard.This standard also covers the indirect actuation of the switch when the operation of theactuating member or sensing unit is provided by a remote control or a part of an appliance orequipment such as a door.NOTE 1 Electronic change-over selectors may be combined with mechanical change-over selectors giving fulldisconnection or micro-disconnection.NOTE 2 Electronic change-over selectors without a mechanical switch in the supply circuit provide only electronicdisconnection. Therefore, the circuit on the load side is always considered to be live.NOTE 3 For change-over selectors used in tropical climates, additional requirements may be necessary.NOTE 4 Attention is drawn to the fact that the standards for appliances may contain additional or alternativerequirements for change-over selectors.NOTE 5 Throughout this standard, the word \"appliance\" means \"appliance or equipment\".1.2 This standard applies to change-over selectors intended to be incorporated in, on or withan appliance.1.3 This standard also applies to change-over selectors incorporating electronic devices.

BS EN 62094-1-2003家用和類似用途的固定電氣設施用指示燈部件.一般要求

This International Standard applies to stand-alone indicator light units intended to give a visible signal. They are designed for a.c. only with a rated voltage not exceeding 440 V and a rated power not exceeding 10 W, for household and similar fixed-electrical installations, either indoors or outdoors.\nNOTE 1 Indicator light units are not intended for lighting as a luminaire (see IEC 60598).\nThis standard does not apply to pilot lights incorporated in products complying with their own standards which are tested as part of that product.\nThe standard also applies to boxes for indicator light units, with the exception of flush-mounting boxes (according to IEC 60670) for flush-type indicator light units.\nIndicator light units complying with this standard are suitable for use at ambient temperatures not normally exceeding 25 ℃, but occasionally reaching 35 ℃.\nIn locations where special conditions prevail, as in ships, vehicles and the like and in hazardous locations, for example where explosions are liable to occur, special constructions may be required.\nNOTE 2 LEDs and lamps are not considered as indicator light units, but as components.

KS C IEC 60669-1-2008家用和類似用途固定電氣設備開關.第1部分:通用要求

? ??? ??? ? ?? ??? ??? ?? ?? ??? ???? ?? ?? ??? ??